5.7″ G2H2

Part Number: 51-0406-081

  • Comes with a VGA (640×480) display.

Powered by the G2H2 controller:

  • A wide range of input/output (I/O) ports including one RS-232 serial port, one RS485, two USB 2.0 host ports, a CAN interface, 10/100 Ethernet, I2C, a CMOS serial port, and GPIO.

  • NXP i.MX 6Solo, 1.0 GHz Processor including hardware video decoder and 3D graphics engine. 512 MB DDR3 DRAM. 512 MB NAND Flash / 16 MB NOR Flash. microSD Flash Card Socket. Audio Codec with 1 Watt Audio Amplifier and Speaker.

All 5.7″ modules feature:

  • An industrial panel with resistive touchscreen. Compare touch types.

  • Designed for long-term availability with a 10+ year processor life and a multi-sourced, industry standard LCD form factor.

  • ESD and EMC results available to ease regulatory compliance testing.

G2H2 Controller

  • CPU: NXP i.MX 6Solo, 1.0 GHz Processor including hardware video decoder and 3D graphics engine.
  • Storage Capacity: 512 MB DDR3 DRAM. 512 MB NAND Flash / 16 MB NOR Flash. microSD Flash Card Socket.
  • I/O Interface: 10/100/1000 Mbps Base-T Ethernet: Features low profile Molex Pico-SPOX Connector (24 AWG Compatible). One RS232 and one 3.3V CMOS Serial Port. One RS485. One USB 2.0 (High Speed) Host Port. One USB 2.0 (High Speed) On-The-Go (OTG) Host Port. One I2C Port. One CAN Bus with Transceiver. 8-bit GPIO Port 5V Tolerant.
  • Audio: Codec with 1 Watt Audio Amplifier and Speaker

LCD Display

  • Display Type: 5.7″ Diagonal TFT Color LCD
  • Resolution: 640 x 480 VGA, 18-bit Color
  • Orientation: Landscape
  • Luminance (with touch): Typical 620 (cd/m²)
  • Viewing Angles: 65/65 left/right, 60/70 up/down
  • Backlight: LED
  • Manufacturer: Evervision

Get detailed panel specifications.

Touchscreen

  • Type: 4-Wire Analog Resistive
  • Touch Driver: Standard Linux Driver
  • Durability: Over One Million Touches

Dimensions

6.325” W x 4.118” H x 1.054” D

Environmental/Regulatory

  • Operating Temperature: 0 to 70° C; Contact us for extended temperature.
  • Storage Temperature: -30 to 80° C
  • Humidity: Max 90%RH at 60° C; No Condensation
  • RoHS 2 Compliant: Yes

Power Requirements

  • Power Supply Voltage: +5VDC (5.15V for 5V USB Host Port Power Out)
  • Power Consumption: Max 970mA during boot with no devices attached.

Grounding

The G2H2 module requires a 5V DC input, +/- 5%. At boot-up, it uses a maximum of 970 mA with no external devices attached. If the module is supplying power to external USB devices (500mA max.), the input power should be a minimum of 5.15 V to meet the USB specification at the far end of the longest USB cable run. The module can also supply +5V to other external devices on some of the connectors, and all such supplies need to be considered in the power budget. The input power connector can handle 3A of nominal 5V input.

The board mounting holes are connected to digital ground. These must be connected to chassis ground either directly or through a transient protection diode for ESD.

Mounting Options

For 5.7″ modules, Reach Technology provides gaskets. Visit Mounting Options for more information.

Software Releases

Download a new software release by selecting the appropriate model and kernel image from the table below (usually the latest version). Then visit the SD Card section for a discussion on tools you can use to install the new software on your SD card.

Part NumberDateChange LogFile SizeImageSoftware Documentation
S060-00202/01/2018This is the initial release for the G2H2-5P (Full I/O) display module.416 MBS060-002 lockG2H-V1-8

See how to get your development kit set up, learn more about QML development, see Application Notes, and more resources to get started in G2H v1.8 Software Documentation.

This video shows you how to get your kit up-and-running once it arrives.

See how to set up an application, design your first screen, and download code to the module. These videos were created using a 7″ display module yet apply to this 5.7″ module.

See how to set up an application, design your first screen, and download code to the module. (Note: Instead of using 800 x 600 to define the rectangle dimension of a 7″ screen as shown at 1:16 minutes into the video, change “Rectangle Width” to “640” and “Rectangle Height” to “480” for the 5.7″ screen).

Find more tutorial resources.

5.7” G2H2 Resistive Development Kit

Part Number: 52-0406-081
$619

Add to Cart

Embedded Touchscreens Made Easy:
Up in Days, Smoothly to Production. Get started with a Development Kit.

Reach Technology is now a part of Novanta.

Corporate
5750 Hellyer Avenue
San Jose, CA 95138
408-754-4176
info@reachtech.com

Research & Development
155 ‘B’ Avenue, Suite 200
Lake Oswego, OR 97034
503-675-6464
techsupport@reachtech.com

Manufacturing
4600 Campus Place
Mukilteo, WA 98275
service@reachtech.com